to work in an officefurnitureUnder the background of rapid economic and social development, it is not only the material product, but also the artistic value. But facing the market an array of all kinds of products, how to to companies or individuals to pick a bed of roses, durable office furniture, many consumers are not the end in mind. To this end, a small series of office furniture to buy the main points of a classification summary.

Reasonable timber

      office furniture is different, the surface of the material also will be different. asdesk,chairCabinet legs, with a hard Zamu asked, relatively strong, capable of bearing load, and the internal materials are availableMaterial Science. howeverSolid wood furnitureOr a large number of Large Firm to buy the main object.

Four smooth

& nbsp; & nbsp; & nbsp; this is very simple, the selection will objects placed on the ground in a flash glance, some furniture is only three legs fall to the ground. In addition, the observation of the desktop is straight, can not bow back or down the waist. The desktop, glass will be placed on spin; recessed desktop, I put pressure on the glass broken.

Smooth edge

      edge should be rounded, not straight edge at right angles. If the edge uneven, indicating that the material is wet, easy to crack edge. Three plywood package with the furniture, the package is a nail nail, should pay attention to whether the nail eye level, the nail eye department and other colors are consistent. Normally nailhole is sealed with putty, if bulging putty, not pretty easy to fall out.

Strict close seam

      joint in whether PVC, paste veneer, or stickpaintPaper should observe whether leather paste was smooth, without bulge, blistering, patchwork lax phenomenon. Look at the light in the examination, otherwise it is not easy to see. Ash wood veneer furniture is easy to be damaged, the service life of two years. Wood veneer alone, the plane side of the veneer peeling than good. General veneer furniture corner where easy to raise up, when you can pick a hand to pull the bottom corner, if a pull on the up, that the problem with plastic.

Pay attention to environmental protection

      office furnitureenvironmental protectionThe problem is that each user is concerned, the purchase should be asked to ask whether the furniture is in line with the relevant national environmental regulations, and hope the other to produce the relevant certification, etc.. But buying is furniture brand, careful inquiry and please sales personnel to smell to make a reasonable explanation, while viewing the inspection certificate, national inspection did pass, furniture containing a small amount of odor is paint, adhesives and other necessary incidental, after the home to open the cabinetdoorFor some time to eliminate.

Low water content

      high moisture content furniture not only has the quality problem, but also increase the formaldehyde release rate, which seriously affects the health of the users. Office furniture moisture content shall not exceed 12%, otherwise there will be a wood warping, deformation phenomenon, a serious impact on the service life of office furniture. General consumers purchase, by touch, hand touch furniture bottom surface or inside the unpainted place, if you feel dry, so water content at least in more than 50%, there can not be used. Another way is to have painted wood. Sprinkle a little water, if Yin slowly or not down, indicating high moisture content.

Check out

      wood drying is not complete, there will be taken out at the end of. After the complete surface inspection, should also open the door,drawerThe door to see inside the material has not decadent, you can use a fingernail pinch pinch, pinch into a is described in the decay of the material (required by the Seller agrees to undertake). In the nose after the doors opened, such as a red nose, glare, the formaldehyde content in cement is too high, will be harmful to the human body.

Reasonable parts

      metal parts, plastic partsPanel furnitureThe main use of the fastening connection pieces, so the quality of the metal parts at the same time decided toPlateThe advantages and disadvantages of the inherent quality of furniture. The metal parts requirements neat, smooth, good plating surface treatment, especially not rust, burr, with a precision requirements higher. Plastic parts to be beautiful, bright colors, the use of the focus areas to have strength and elastic, can not be too thin. The doors open type joints flexible, with internal springs is proper tightness, such office furniture in the open use will be balanced, relaxed, no friction sound.

Article source: office furniture
European Furniture Xianghe furniture city official website How beautiful furniture American furniture Antique furniture Furniture factory Single bed Traction bed The shelf bed The latex mattress Nature mattress Dunlop mattress Table tennis table size Children learning table Ten brands of solar water heater Cabinet top ten brand ranking Ten major brands of fabric sofa The friends of furniture. Federal furniture Chivas sofa Federal furniture Tianjin IKEA Nanjing IKEA Ramsa furniture Beautiful home STANLEY wardrobe Ten wardrobe brands Holike wardrobe. TV cabinet effect chart